Memory if Full - FrontPanelDataController
Hi, I am receiving a Memory if Full error in the executable that I've build from LabVIEW 2010 SP1, and it says that my vi was stopeed at FrontPanelDataController "Error Out". See the attached jpg...
View ArticleTime values in logged thermocouple data not realistic
I'm in desperate need of LabVIEW programming help! When the run arrow is clicked, my VI is designed to simultaneously start logging filtered thermocouple data and send a TTL-type pulse out of a CTR...
View ArticleLabview array to graph
I am reading data from modbus and have an array of data that I need to graph, deepending on the iteration of a for loop I want to direct the data to the right struture and plot it. What plot should I...
View ArticleMissing DAQmx Resources
After recently upgrading my NI-MAX from version 7 to version 9.7.5 whenever I try to access any of my projects that require accesss to DAQ they are unable to find the required libraries, even after...
View Articlewinusb and visa device issue
I have a system I am working on that communicates with some custom hardware via USB. I used the NI driver wizard to create some visa drives, and perform USB RAW writes and reads, and everything was...
View ArticleLabVIEW and Force Feedback via DirectInput
Hello, I looked around and saw several open questions on this, but no one with a working prototype. So I started working on this for for a school project. I've come up with a basic working sample....
View Articletcp ip
urgent. i am sure there is a little thing wrong on the solution .can somebody help me here :...
View Articlehow to make RT -RT communication in between two sbRIO
hello i want to make a redundant system using two Sbrio board...can u please help me how to start on with this...
View ArticleLV2012 SP1 Get LV Class Default Value Error 1498
Dear all,I'm facing with a problem similar to others with the Get LV Class Default Value, but I preferred to open another discussion because of the differences.We have developed a project with LV2012...
View ArticleHost/FPGA/CLIP Synchronization
I have been developing some continuous acquisition from RIO hardware and I have spent at least a week being stuck, so I finally I decided to help. Things almost work but not reliably. I am attaching my...
View ArticleArduino interface does not work with renamed VIs
I installed the LabVIEW- Arduino interface and every example runs fine. However, when I rename my application I get the error "This VI is connected with a library that does not include the VI. The VI...
View Article[FPGA] Question about testing on dev computer
I have an FPGA vi that I want to test on my development computer with the method shown here: http://zone.ni.com/reference/en-XX/help/371599G-01/lvfpgaconcepts/test_bench_tutorial/ All well and good so...
View Article擷取資料問題(原本正常，突然無法抓值)
我使用DAQ USB-6361搭配LabView抓值功能來抓取電壓訊號，一次2000筆 但前陣子再一次重新使用時發生問題，問題點: 為何之前可以運作程式，突然就不行抓值 第一 是否是DAQ傳輸線的問題(接腳看不到有無斷PIN，DAQ使用兩年) 第二 是否是Labview軟體DAQ訊號程式的問題(基本上之前好好的都沒去更改)...
View ArticleHow to zero padd array
Hi guys I am trying to perform zero padding.I am having 512 by 512 array and I want to add 256 rows of zeros above and below of my array so as my new array will be 1024 by 512,where 1st & last 256...
View ArticleI can't install LabVIEW due to, "NI LabVIEW 2012 SP1 32 bit must be installed...
Attached is the message that I get while attempting to install Lego Mindstorms NXT. Please help, thanks.
View Articlemyrio gps
http://www.youtube.com/watch?v=SebcpkbYBd4 I am currently using the adafruit GPS sensor and connecting to the myrio. I was following along with the example above, due to it being a patch antenna and...
View Articlehow to customize the fifo in sbrio 9642
i am using sbRIO 9642 for controlling the speed of the fan on sound and vibration signal simulator against vibrations i want to use FIFO buffer in order to collect those data poitns how can i...
View Articlehow to demodulate the infrared signal in LabVIEW
Hi, I hope some one can share your knowledge on how to demodulate the infrared signal using LabVIEW. I modulate the infrared (IR) light using the counter pulse generation with frequency of 500Hz and...
View Articlebreak large TDMS file into small files
hello all My TDMS file is around 3g, and needs changed into around 10M size files. I ran McRorie's splitFiles.vi 15 KB in this page. and set the number of samples per file as 5000000, however, I...
View Article